Rev 04.08.021 - 1 – CV Series User ManualUser ManualUser ManualUser Manual This User Manual is made available in Adobe Acrobat format. In order
Rev 04.08.021 - 10 – CONTROLS AND FUNCTIONS 1. Rack Mount Ears The ears for rack mounting the CV Series amplifiers are removable.
Rev 04.08.021 - 11 – 5. CV Series Model Number The Model number should be interpreted as follows: The last digit of the mode
Rev 04.08.021 - 12 – 1. Serial Number The Serial Number is used by Carver Professional to track units and establish their warranty
Rev 04.08.021 - 13 – 4. Remote Level The Remote Level Connector is used to connect a Remote Level Control to the CV Series amplifier. The connect
Rev 04.08.021 - 14 – Figure 7 CV Series amplifier. If your application requires rack mounting, optional line cords, shorter than the standard 2 me
Rev 04.08.021 - 15 – amplifier’s chassis structure to the rear of the rack during transportation. This practice is recommended for all electronic c
Rev 04.08.021 - 16 – Another input to the CV Series amplifiers is provided via the EFX Loop’s RCV (receive) input. This input is only available w
Rev 04.08.021 - 17 – Figure 8 (+) 70V Mono Load (-) output of the CV2502 to create a Mono 70V output at 500 Watts. Connect the positive (+) lead f
Rev 04.08.021 - 18 – Figure 9 Figure 10 Important Note: When bridging the CV Series amplifier at one of the distributed voltage outputs, it is ne
Rev 04.08.021 - 19 – Figure 11 12VDC Supply amplifiers in the sequence are connected. Connect the negative side of the DC supply to the chassis gr
Rev 04.08.021 - 2 – CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER. NO USER SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALI
Rev 04.08.021 - 20 – Figure 13 Using Other Amplifiers in the Power Sequence The Carver pm700, pm950, pm1400, pt1800 and pt 2400 can be use togethe
Rev 04.08.021 - 21 – and CV2 terminals. If you wish to control both channels simultaneously, using the remote control as a master level control an
Rev 04.08.021 - 22 – Figure 17 Using Third Party Control Systems Other manufacturers such as Crestron®, AMX® and PANJA® supply systems frequently
Rev 04.08.021 - 23 – WARRANTY INFORMATION CV Series Power Amplifiers: 5 Years CV Series Modules and Accessories: 1 Year NOTE: The following war
Rev 04.08.021 - 24 – CARE AND SERVICE ASSISTANCE Care: Wipe off the CV Series Amplifier’s front panel and chassis from time to time, with a soft,
Rev 04.08.021 - 25 – Distortion Distortion is usually caused by excessive loss in the input controls (the mixer/equalizer/crossover cannot produce
Rev 04.08.021 - 26 – Appendix “A” Power Consumption for CV Series Amplifiers CV Series AC Power Considerations 1kHz Sine Wave @ Full
Rev 04.08.021 - 27 – Appendix “B” Input Sensitivity Jumpers 101 and 102 on the standard input module’s PCB are used to set the Input Sensitivity
Rev 04.08.021 - 3 – INTRODUCTION Congratulations on your purchase of a new Carver Professional CV Series Power Amplifier. The CV Series amplifier
Rev 04.08.021 - 4 – CV1501 CV2501 Power Output Power Output • 150W mono into 4 ohm and 8 ohm loads, • 250W mono into 4 ohm and
Rev 04.08.021 - 5 – SPECIFICATIONS with Basic input module PERFORMANCE: •••• THD: <0.5% @ rated power, 0.2% 1/8 rated power at1
Rev 04.08.021 - 6 – CV1502 CV2502 Power Output Power Output • 150W per channel into 4 ohm and 8 ohm loads, • 250W per channel i
Rev 04.08.021 - 7 – SPECIFICATIONS with Basic input module PERFORMANCE: • THD: 0.5% at rated power, 0.2% at 1/8 rated power at 1
Rev 04.08.021 - 8 – CV4002 Power Output • 400W per channel into 4 ohm and 8 ohm loads, autoformer coupled, 40Hz to 20kHz ±3dBwith &l
Rev 04.08.021 - 9 – SPECIFICATIONS with Basic input module PERFORMANCE: • THD: 0.5% at rated power, 0.2% at 1/8 rated power
Commentaires sur ces manuels